Gate Sizes for Fences: Standard Dimensions
Standard gate sizes for fences, how to measure an opening, and gate kits that fit common chicken run gates.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Fence Gate Kit Gate Hardware9.6/10View on Amazon - 2
Adjust-A-Gate Steel Frame Gate Kit, Black9.5/10View on Amazon - 3
2Pcs Adjustable Heavy Duty Fence Gate Kit 36-72"9.5/10View on Amazon - 4
GoldOrcle Anti Sag Gate Kit Heavy Duty No Sag Kit9.3/10View on Amazon
The gate is the part of the run you touch on every visit, at feeding time and again at dusk when the flock goes in. A gate that drags, sags or will not latch turns a short chore into a wrestle with the fence, and gate sizes for fences are the measurements that keep that from happening.
CoopKeeperHQ earns a commission if you buy through our links, at no added cost to you. Affiliate disclosure.

Fence Gate Kit Gate Hardware
A steel gate kit with a self-closing spring and self-locking latch, stated safe loading of 200 lbs, for wood gates of 2 in by 4 in and above.
Who it's for: a keeper who wants the gate to shut and lock on its own, with the strongest stated load here.
Who should skip it: anyone who needs a stated width range or a written warranty.
WEKIS lists safe loading of 200 lbs and a steel build with a powder-coating rust-resistant finish. The kit holds a gate of 2 in by 4 in wood and above, and the pack lists 2 gate hinge brackets, 4 corner brackets, 1 self-closing spring, 1 gate latch, 1 bar, 1 pull ring with wire and screws at 1 in, 1.6 in and 1.4 in.
Pros
- Safe loading of 200 lbs, the highest stated here
- Self-closing spring and self-locking latch included
- 20 short screws (1 in), 20 long screws (1.6 in), 6 latch screws (1.4 in)
- Suits wood gates of 2 in by 4 in and above
Cons
- No warranty term is stated
- No gate width range is stated
- Title spells 'Corner' as 'Cornor' and 'Hinges' as 'Hings'
- Spring and latch add parts to fit and adjust

Adjust-A-Gate Steel Frame Gate Kit, Black
An adjustable steel frame kit for openings from 36 to 60 inches and up to 7 ft high, with a truss cable and a limited 1 year warranty.
Who it's for: a keeper with a wide opening who wants a steel frame and a written warranty.
Who should skip it: anyone who needs a stated load figure or boards in the box.
Adjust-A-Gate lists a steel frame that adjusts on site for openings from 36 to 60 inches and up to 7 ft high, with telescoping spreader bars. The truss cable system holds the frame straight, and the kit takes wood or composite boards to match the fence. The spec table lists the product dimensions as 0.0 in, so the title and bullets carry the sizing. The listing states a limited 1 year warranty on defects and workmanship
Pros
- Adjusts for openings from 36 to 60 inches with no cutting
- Fits openings up to 7 ft high
- Truss cable system holds the frame straight
- Limited 1 year warranty on defects and workmanship
Cons
- No safe loading figure is stated
- Wood or composite boards are not included
- Warranty covers defects and workmanship for a limited 1 year only

2Pcs Adjustable Heavy Duty Fence Gate Kit 36-72"
A 2-pack of adjustable steel gate frames for openings from 36 to 72 inches on fences 4 to 5 ft high, with an anti-sag truss cable.
Who it's for: a keeper framing a wide gate on a 4 to 5 ft fence who wants a spare frame in the pack.
Who should skip it: anyone who needs a latch, a stated load figure or a written warranty.
Sidasu lists a 2-pack of steel frames with telescoping bars for gate openings from 36 to 72 inches, made for fences 4 to 5 ft high and wood of 1 in by 4 in and 2 in by 4 in. The adjustable anti-sag diagonal truss cable holds the frame square, and a UV-resistant powder coating guards the steel. The listing gives 2 replaceable clips with the 2-pack.
Pros
- Widest range here: openings from 36 to 72 inches
- Suits fences 4 to 5 ft high
- 2 replaceable clips and a truss cable against sag
- UV-resistant powder coating for outdoor use
Cons
- No warranty term is stated
- No safe loading figure is stated
- No latch is named in the listing
- Wood or composite boards are not included

GoldOrcle Anti Sag Gate Kit Heavy Duty No Sag Kit
A steel anti-sag kit with a gate latch, a 180 degree swing and safe loading of 120 lbs, with assembly listed at 25 minutes.
Who it's for: a keeper fixing a sagging wooden gate who wants a latch in the box.
Who should skip it: anyone who needs a wider stated load margin, a stated width range or a written warranty.
GoldOrcle lists a heavy duty steel kit with a powder-coating rust-resistant finish and safe loading of 120 lbs, made to hold a new gate straight or repair a sagging wooden gate. The kit swings 180 degrees left or right and includes 2 gate brackets with attached hinges, 2 non-hinged gate brackets and a gate latch, with assembly listed at 25 minutes and no special tools.
Pros
- Swings 180 degrees left or right
- Assembly listed at 25 minutes with standard screw sizes
- Safe loading of 120 lbs stated
- Suits wooden fence gates, deck gates and shed doors
Cons
- No warranty term is stated
- 120 lbs is the lower stated load here
- No gate width range is stated
- No self-closing hardware is included
Gate sizes for fences: standard widths and heights
The adjustable frames in this guide cover a band of widths: the Adjust-A-Gate frame adjusts for openings from 36 to 60 inches, and the Sidasu frame adjusts from 36 to 72 inches. Height follows the fence: the Sidasu kit suits fences 4 to 5 ft high and the Adjust-A-Gate kit fits openings up to 7 ft.
Measure the opening before you buy
Measure the gap between the posts at the top and at the base, then use the smallest reading to pick a frame. The opening decides the kit, and the Adjust-A-Gate kit needs no cutting at all. If the posts need setting, see whether fence posts should be set in concrete.
Match the gate height to the fence
A gate that stands shorter than the fence leaves a gap at the top, and a taller gate catches the wind. The Sidasu kit is made for fences 4 to 5 ft high, and the Adjust-A-Gate kit fits openings up to 7 ft. For help with the height of the run itself, see how tall a chicken run should be.
Gate kits that fit the opening
The kits below frame the gate after the opening is measured.
What the load rating tells you
The safe loading figure is the load the maker says the hardware can carry. The WEKIS kit states safe loading of 200 lbs, and the GoldOrcle kit states safe loading of 120 lbs. A gate with boards, a latch and a spring puts its load on the hinges and brackets. The Adjust-A-Gate and Sidasu listings state no safe loading figure.
Hinges, latches and self-closing springs
The WEKIS kit adds a self-closing spring and a self-locking latch, so the gate shuts behind you and the bar drops into the latch. The GoldOrcle kit swings 180 degrees either way, left or right, so it opens flat against the fence. Assembly stays simple: the GoldOrcle listing states assembly in 25 minutes with standard screw sizes and no special tools, and the WEKIS listing says the project needs no professional skill. For the latch itself, see the chain link gate latch guide.
A quick gate checklist
- Opening measured top and base
- Frame range covers the width
- Gate height matches the fence
- Latch shuts and holds
- Hinges carry the load
Wash your hands after handling birds, eggs or equipment, supervise children around the flock, and check local rules on flock size and roosters before you buy. For sick birds, call a poultry veterinarian or your state extension office. See CDC backyard poultry guidance. Read our Safety Disclaimer.
FAQ for the flock
What gate size fits a chicken run gate?
Match the frame to the opening: the Adjust-A-Gate frame adjusts for openings from 36 to 60 inches and the Sidasu frame from 36 to 72 inches.
How tall should a gate be for a chicken run fence?
Match the gate to the fence: the Sidasu kit suits fences 4 to 5 ft high, and the Adjust-A-Gate kit fits openings up to 7 ft.
Is a self-closing latch worth adding to a chicken run gate?
A self-closing spring shuts the gate and a self-locking latch holds it. The WEKIS kit includes a self-closing spring, a self-locking latch, a bar and a pull ring with wire.
What holds a wide gate from sagging?
An anti-sag truss cable and a steel frame carry the load: the Adjust-A-Gate kit uses a truss cable system, the Sidasu kit uses an adjustable anti-sag diagonal truss cable, and the GoldOrcle and WEKIS kits use steel brackets.
What size gate wood does a gate kit fit?
The WEKIS kit suits wood gate sizes of 2 in by 4 in and above, and the Sidasu kit fits 1 in by 4 in and 2 in by 4 in wood.
More coop guides
- Chicken Run Set Up: A Step-by-Step Guide
- Chain Link Fence Post Size: Terminal, Line and Rail Sizes
- How Tall Should a Chicken Run Be? A Practical Guide for Backyard Flocks
- Should Fence Posts Be Set in Concrete? What to Use Instead
- Chain Link Fence Gauge Chart: What the Numbers Mean for a Chicken Run
- Field Fence vs Poultry Netting: Which One Should You Buy?
- Wood vs Steel Fence Posts: Which One Should You Buy?
- Best Fence to Keep Chickens Out of Garden (2026): 5 Picks for Beds and Borders
- How to Use Chain Link Fence Ties
- Best Chicken Wire Ties (2026): 5 Coop and Run Picks
See the chicken runs and fencing picks for more run and fence guides.




