How to Hang a Gate With Hinges
A level gate starts with a firm post, hinges matched to the gate, and leaves fixed square so the latch meets its catch.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Letowe Heavy Duty Gate Hinges 7 Inches9.5/10View on Amazon - 2
Insaga Heavy Duty Gate Hinges9.5/10View on Amazon - 3
Wmebee 4 Pack 5 in T Strap Heavy Duty Gate Hinges9.5/10View on Amazon - 4
HOME MASTER HARDWARE 10 in Heavy Duty Gate Hinges9.4/10View on Amazon
The run gate hangs crooked, the latch misses its catch, and the hens crowd the doorway while the gate drags on the ground. Learning how to hang a gate with hinges fixes that sag: each hinge has a leaf that fastens to the post and a leaf that fastens to the gate frame, and the gate swings level on the pins.
CoopKeeperHQ earns a commission if you buy through our links, at no added cost to you. Affiliate disclosure.

Letowe Heavy Duty Gate Hinges 7 Inches
A 7-inch weld-on barrel hinge with a stated 900 lbs capacity, a grease fitting nipple for the ball bearings, and extra thick back plates.
Letowe lists the 7-inch barrel hinge at 900 lbs capacity, with solid steel leaves, extra thick back plates and a matte black coating that resists corrosion and rust. A grease fitting nipple keeps the internal ball bearings lubricated, and the maker also lists a 5-inch size rated at 450 lbs. Each order holds 2 hinges.
Pros
- 900 lbs stated capacity for the 7-inch size, the highest here
- Grease fitting nipple keeps the ball bearings lubricated
- Extra thick back plates for a firm weld-on fit
- Matte black coating resists corrosion and rust
Cons
- Weld-on fitting only, so it suits metal gates and needs welding gear
- No screws or bolts are stated in the box
- The stated 900 lbs capacity applies to the 7-inch size only; the 5-inch size is rated at 450 lbs
- No warranty term is stated

Insaga Heavy Duty Gate Hinges
A 4-pack of 4.9 in hinges in thick 6 mm high-strength steel, with a 600 lb load capacity per pair, a 5/8 in hinge pin and an electroplated finish.
Insaga lists the hinge at 4.9 in long by 1.5 in wide, in thick 6 mm high-strength steel with a 5/8 in hinge pin and 1/2 in mounting holes. Each pair carries up to 600 lb, and the electroplated finish guards against rust, UV damage and harsh weather. It fits wooden or metal gates, fences and shed gates, with wood screws for wood and expansion bolts for concrete.
Pros
- 600 lb load capacity per pair
- Thick 6 mm high-strength steel leaves
- Electroplated finish guards against rust, UV damage and harsh weather
- 5/8 in hinge pin with 1/2 in mounting holes for wood or metal gates
Cons
- The 600 lb figure is per pair, so one hinge carries less on its own
- Needs pre-drilled holes, so fitting takes more prep
- No warranty term is stated
- Mounting holes are 1/2 in, so the bolts or screws must match that size

Wmebee 4 Pack 5 in T Strap Heavy Duty Gate Hinges
A 4-pack of 5 in T-strap hinges in 0.11 in thick solid steel, with a 260 lbs capacity in pairs and 32 mounting screws in the box.
Wmebee lists the T-strap hinge at 5 in long, in 0.11 in thick solid steel with a black coating finish, and states a 260 lbs capacity when the hinges work in pairs. The swivel part measures 5 in by 2.1 in, the fix part measures 5 in by 1.8 in, and the box holds 4 hinges with 32 mounting screws that are 1.2 in long. The holes sit in drilled pits, and the offset screw holes add strength and help stop wood splitting.
Pros
- 260 lbs capacity when used in pairs
- 0.11 in thick solid steel with drilled pits that fit the screws
- 32 mounting screws included with the 4 hinges
- Offset screw holes add strength and help stop wood splitting
Cons
- The 260 lbs capacity needs both hinges used together
- At 5 in long it gives less leverage than the 10 in T-strap hinge
- Screw length is 1.2 in, so a deeper bite needs longer screws
- No grease fitting or bearing is stated, so the swing relies on the plain steel leaves

HOME MASTER HARDWARE 10 in Heavy Duty Gate Hinges
A 4-pack of 10 in T-strap hinges in iron with a black powder coat, a 270-degree swing, silent washers and a 70 lbs capacity per piece, with screws in the box.
HOME MASTER HARDWARE lists the T-strap hinge at 10.0 in by 6.0 in by 0.1 in, in iron with a black powder coat that resists corrosion, oxidation and rust. Each piece carries 70 lbs, the hinge swings 270 degrees, and silent washers keep the movement smooth and quiet. The box holds 4 hinges with the mounting screws, and offset screw holes add strength and help stop wood cracking.
Pros
- 270-degree swing for gates that open wide
- 70 lbs capacity per piece with a 4-pack in the box
- Silent washers for smooth, quiet movement
- Offset screw holes add strength and help stop wood cracking
Cons
- 70 lbs per piece is the lowest capacity here
- Iron leaves are 0.1 in thick, thinner than the Wmebee and Insaga steel here
- The 10 in length needs a gate frame and post with room for the full strap
- Silent washers are stated, but no bearing or grease point is named
How to hang a gate with hinges: check the post and the gate frame
Start with the post. It should stand firm and upright, with no wobble when pushed by hand. A post that shifts will let the gate sag no matter how well the hinges fit, so firm it up before hanging anything. Check the gate frame for firm joints and straight rails, and clear the ground where the gate swings.
Pick hinges that match the gate
Hinges here fit in different ways: T-strap hinges that screw to the face of the gate and the post, a flat steel hinge that screws or bolts on, and a barrel hinge that welds to metal gates. Match the stated load capacity to the gate: the picks below state 70 lbs per piece, 260 lbs per pair, 600 lb per pair and 900 lbs for the 7-inch weld-on hinge. The 10 in T-strap pick suits a light run gate, a weld-on barrel hinge suits a metal driveway gate, and the gate hinge types guide compares the common kinds.
Mark the hinge spots and fix the leaves
Hold the gate level in the opening and mark the hinge spots on the post and the gate frame, then fix the post leaf first so the gate hangs from a firm anchor. Drive the screws into sound wood, or set the expansion bolts for concrete where the maker calls for them, and keep the leaves flat against the frame. For the weld-on hinge, the leaves weld to the metal gate and post instead of screwing on. Where the maker calls for pre-drilled holes, drill them before fitting, then check the swing before driving the last screws home.
Hang the gate and check the swing
Set the gate on its hinges, then open it through its full swing. The HOME MASTER T-strap pick swings 270 degrees, so a gate that opens flat against the fence is no surprise. Watch the latch side as the gate closes. If the latch misses, loosen the screws a little, shift the leaf, and tighten again. A gate that drags on the ground needs the hinges moved or the frame eased, not forced.
Gate hinges for the run
The hinge choice decides how the gate hangs, so match the hinge to the gate frame, the post, and the load the hinge must carry.
Keep the gate swinging freely
A hinge that sticks makes the gate drag. The weld-on hinge has a grease fitting nipple that keeps the ball bearings lubricated, so add grease when the swing turns stiff. Check the screws when the seasons change and tighten any that worked loose. The black coatings on these hinges guard against rust. If a hinge leaf bends, swap the hinge rather than bending it back.
Birds, breed size, run time and climate in; coop floor, run space, roost length and nesting boxes out.
Wash your hands after handling birds, eggs or equipment, supervise children around the flock, and check local rules on flock size and roosters before you buy. For sick birds, call a poultry veterinarian or your state extension office. See CDC backyard poultry guidance. Read our Safety Disclaimer.
FAQ for the flock
What size gate hinges do I need?
Match the hinge length to the gate frame and the post. The hinges in this guide run from 4.9 in to 10 in long, and the weld-on barrel hinge is 7 in long with a 900 lbs stated capacity.
How many hinges does a run gate need?
Fit a pair: the Wmebee listing states its 260 lbs capacity for a pair used together, and the Insaga listing states 600 lb per pair. A 4-pack gives a pair for the gate and a pair in reserve.
Can gate hinges be welded to a metal gate?
Yes, the Letowe barrel hinge (on Amazon) is made to weld on, and it suits swing gates, trailer ramps and driveways. The T-strap hinges in this guide screw on instead.
Do gate hinges need grease?
The Letowe hinge has a grease fitting nipple that keeps its ball bearings lubricated. The screw-on hinges here state no grease point, so keep their leaves clean and the screws snug.
Why does my gate sag after hanging?
A sagging gate often means the hinges carry more than their stated capacity, or the screws sit in soft wood. Check the stated capacity, move the hinges to sound wood, and check the post for movement.
More coop guides
- Gate Hinge Types Compared
- Gate Latch Types: How to Choose the Right One
- Gate Sizes for Fences: Standard Dimensions
- Types of Fence Gates for Chicken Runs
- Chain Link Fence Gate Latch Types Compared
- Chicken Run Ideas: Layouts, Netting and Fencing
- How to Predator Proof a Chicken Run
- Types of Wood Fence Posts Compared
See the chicken runs and fencing picks and the chicken run ideas guide.




