Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Best Way to Cut Chain Link Fence Safely

Mark the line, cut one wire at a time with bolt cutters, and mind the sharp ends.

Best Way to Cut Chain Link Fence Safely
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1GRENPRO 14 Inch Bolt Cutter, Cr-V SteelGRENPRO 14 Inch Bolt Cutter, Cr-V Steel9.5/10View on Amazon
  2. 2SPENDINS 14 Inch Bolt Cutter with Drop ForgedSPENDINS 14 Inch Bolt Cutter with Drop Forged9.5/10View on Amazon
  3. 3KSEIBI 141570 Heavy-Duty Mini Bolt Cutter 12 InchKSEIBI 141570 Heavy-Duty Mini Bolt Cutter 12 Inch9.4/10View on Amazon
  4. 4wikmonx 8 Inch Mini Bolt Cutterwikmonx 8 Inch Mini Bolt Cutter9.4/10View on Amazon

A roll of chain link waits by the run, and the fence is longer than the space it has to fill. The best way to cut chain link fence is with bolt cutters, working one wire at a time along a marked line, and minding the sharp ends the cut leaves behind. This guide shows the steps and the cutters.

CoopKeeperHQ earns a commission if you buy through our links, at no added cost to you. Affiliate disclosure.

GRENPRO 14 Inch Bolt Cutter, Cr-V Steel

GRENPRO 14 Inch Bolt Cutter, Cr-V Steel

GRENPRO9.5/10 Keeper Score
i
The Keeper Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 14 in Cr-V bolt cutter with 58-62 HRC edges and 18-20mm jaws that cuts soft steel to 7mm and hard steel to 4mm.

Who it's for: keepers cutting fence wire and small bolts with a full-size cutter.

Who should skip it: anyone working in a tight spot.

GRENPRO lists the 14 in cutter in Cr-V steel with 58-62 HRC edges, an 18-20mm jaw opening, and capacity of 7mm soft steel and 4mm hard steel. The grip is cushioned and non-slip.

Pros

  • Cuts soft steel to 7mm and hard steel to 4mm
  • 18-20mm jaw opening with 58-62 HRC edges
  • Cr-V steel frame at 38-45 HRC with black oxide finish
  • Cushioned non-slip grip for steady holding

Cons

  • No warranty term is stated
  • No safety latch is stated
  • 14 in size needs room to swing in a tight run
  • No weight is stated in the spec table
SPENDINS 14 Inch Bolt Cutter with Drop Forged

SPENDINS 14 Inch Bolt Cutter with Drop Forged

SPENDINS9.5/10 Keeper Score
i
The Keeper Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 14 in Cr-Mo bolt cutter, 1.9 lb, that cuts 7mm at 25 HRC and 5mm at 42 HRC, for fence wire, chains and small bolts.

Who it's for: keepers who want a full-size cutter with a stated weight.

Who should skip it: anyone cutting harder steel.

SPENDINS lists the 14 in, or 350mm, cutter at 1.9 lb, with drop forged Cr-Mo blades. Capacity is 1/5 in, or 5mm, for 42 HRC material and 7/25 in, or 7mm, for 25 HRC material.

Pros

  • Cuts 7mm material at 25 HRC and 5mm at 42 HRC
  • Drop forged Cr-Mo blades, induction quenched and blackened
  • Weighs 1.9 lb at 14 in, or 350mm
  • Eccentric bolts allow clearance adjustment

Cons

  • No warranty term is stated
  • No safety latch is stated
  • Blade hardness tops out at 42 HRC
  • No jaw opening figure is stated
KSEIBI 141570 Heavy-Duty Mini Bolt Cutter 12 Inch

KSEIBI 141570 Heavy-Duty Mini Bolt Cutter 12 Inch

KSEIBI9.4/10 Keeper Score
i
The Keeper Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 12 in mini bolt cutter with a 5/8 in cut range for thin wire, small bolts and nails in tight spaces.

Who it's for: keepers trimming thin wire and small bolts in tight spaces.

Who should skip it: anyone cutting locks or large bolts.

KSEIBI lists the 12 in, or 300mm, cutter in high-quality steel with an anti-rust coating and a soft grip handle. The cut range runs up to 5/8 in, or 16mm, for light-duty work: thin wire, small bolts and nails.

Pros

  • Cut range up to 5/8 in, or 16mm, in diameter
  • 12 in, or 300mm, balances maneuverability and cutting capacity
  • Anti-rust black coating on high-quality steel
  • Soft grip rubber handle for comfort

Cons

  • Not ideal for cutting locks or large bolts
  • No warranty term is stated
  • No safety latch is stated
  • Light-duty cutter, so it suits thin wire, small bolts and nails only
wikmonx 8 Inch Mini Bolt Cutter

wikmonx 8 Inch Mini Bolt Cutter

wikmonx9.4/10 Keeper Score
i
The Keeper Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

An 8 in mini bolt cutter with 65 HRC Cr-V blades and a spring lever for soft wire, copper and craft wire, with a safety latch.

Who it's for: keepers trimming hardware cloth and fine wire.

Who should skip it: anyone cutting hardened steel or a lock.

wikmonx lists the 8 in mini cutter with 65 HRC Cr-V blades and a spring-loaded lever. It cuts soft wire, copper and craft wire, and the listing names hardware cloth among its uses. A built-in safety latch keeps the jaws closed.

Pros

  • 65 HRC Cr-V blades, heat-treated for lasting sharpness
  • Spring-loaded lever multiplies hand force in a one-hand tool
  • Built-in safety latch keeps jaws closed
  • Compact 8 in size fits tool belts and tight spots

Cons

  • Not designed for hardened steel, stainless bolts, or padlocks
  • No warranty term is stated
  • Built for fine bolts and soft wire, not for heavy cutting
  • No weight is stated in the spec table

Other options for the coop

Bolt cutters shear the wire cleanly, while pliers crush it. The long handles give leverage, so the cut takes hand pressure. A short mini cutter works for fine wire and hardware cloth, but a full-size cutter makes the fence cuts easier.

Mark the cut first

Stretch the fence out and mark the cut line first. Chalk or tape shows the line, and a mark you can see keeps the cut straight. Check the line once from the front and once from behind. Measure the opening the cut piece has to fill first.

Cut one wire at a time

Chain link is woven wire, and each wire spirals through it. Set the jaws on one wire at the marked line, close the handles with steady pressure, and let the cutter do the work. Cut the next wire the same way, and work along the line from one end to the other. If a wire resists, reset the jaws square on the wire and cut again rather than twisting the cutter.

Mind the sharp ends

Every cut leaves a sharp end, and a sharp end will snag gloves, scratch arms, and cut a hen that brushes past it. Wear gloves and eye protection, and keep the flock away until the edge is dressed. Fold each cut end back with pliers, or cover the edge with a rail. Our fencing pliers guide shows the grip for folding ends back.

Gear for the job

Bolt cutters do the cutting, and length and jaw size decide which wire the cutter can handle.

A simple checklist

  • Mark the cut line and check it
  • Wear gloves and eye protection before you cut
  • Cut one wire at a time
  • Fold each cut end back with pliers
  • Keep the flock away until the edge is dressed
Flock safety basics

Wash your hands after handling birds, eggs or equipment, supervise children around the flock, and check local rules on flock size and roosters before you buy. For sick birds, call a poultry veterinarian or your state extension office. See CDC backyard poultry guidance. Read our Safety Disclaimer.

FAQ for the flock

Can I cut chain link fence with regular pliers?

Pliers crush the wire and leave a ragged end, while bolt cutters shear it clean. A mini cutter suits fine wire and hardware cloth, but a full-size cutter makes the fence cuts easier.

What size bolt cutter do I need for chain link fence?

A 14 in cutter handles the fence wire: the GRENPRO cuts soft steel to 7mm and hard steel to 4mm, and the SPENDINS cuts 7mm at 25 HRC and 5mm at 42 HRC. A 12 in cutter suits light work, and an 8 in mini cutter suits fine wire.

Do I need to cut every wire?

Cut each spiral wire along the marked line, and the mesh opens as the wires part. Work from one end of the line to the other. A wire you miss will hold the piece, so check the line before you lift it away.

How do I keep the cut edge safe?

Fold each cut end back with pliers, or cover the edge with a rail. Wear gloves while you work, and keep the flock away until the edge is dressed.

Can I reuse the cut piece?

Yes. A cut piece works as a patch for a torn run fence or as a cover for a small gap. Tie it in place, fold the ends back, and check for sharp ends.

More coop guides

See the chicken runs and fencing guides and the wire mesh cutting guide.

More buying guides

Chicken Runs and Fencing ·

What Is a Fence Stretcher? Tool Guide

A fence stretcher is a tool that pulls sagging wire or mesh taut between posts so a chicken run fence stays tight and neat.